Showing results: 271 - 285 of 602 items found.
-
Circuit Check, Inc.
Circuit Check matches top side test targets to your specification and needs. The Signature Series pneumatic drive fixture is the industry standard for precision, accuracy and repeatability.Today’s fifth generation Pneumatic drive supports as many as 8,000 test probes with centerline spacing to 25mil, and contacting test pads as small as 0.014″.
-
IT Series -
Physitemp Instruments
Physitemp multisensors are made with our specially manufactured thermocouple wire. We test and grade this wire to standards better than the accepted ''Special Limits of Error'' and guarantee 0.1°C accuracy in the range of 0-50°C . All multisensor probes conform to NIST standards. These multisensor probes are custom-made and should be ordered to your requirements on number of sensors and spacing between sensors.
-
SWAT WiTrak -
Alethea Communications Technologies Pvt Ltd
SWAT WiTrak is a remotely managed Portal and Field Probe solution that generates 4 to 32 full functionality clients from each device. Probes, can be managed and configured from the portal, Runs Real Applications, Supports different Security Options and Executes pre-defined test sequences. The portal allows the user to generate actionable reports and export raw logs for further analysis.
-
AEMC Instruments
Comprehensive line of clamp-on current probes covers the entire spectrum of applications, from electrical panels to substations. AEMC Current Probes measure current without interrupting the circuit under test and extend the measuring capabilities of DMMs, recorders, power meters, and loggers. The numerous jaw sizes are designed to accommodate a wide variety of conductor diameters and ranges. Available for AC or DC measurements.
-
SONOSCAN T -
SONOTEC GmbH
The ergonomic dual element probes for Non-Destructive Testing from the SONOSCAN Series comply with the DIN EN 12668-2 Standard and can be used to test metals, plastics and ceramics for imperfections such as cracks, inclusions, blowholes and other discontinuities. The transmitter-receiver probes manufactured in Germany are powerful, robust ultrasonic transducers which are compatible with the ultrasonic flaw detector SONOSCREEN ST10 or the thickness gauge SONOWALL 70.
-
28640 -
Lisle Corp.
The tester kit tests low voltage up to 28 volts. Also finds electrical shorts, checks polarity, detects battery drain, and checks circuits from a distance. Heavy-duty coil cord extends over 8 feet. Detachable, spring-loaded hook pulls the center of the wire into the probe every time. Attach alligator clip to the probe when a clip-on connection is needed.
-
EM-6980 | 20 Hz – 50 KHz -
Electro-Metrics Corp.
Current probes enable you to measure conducted current without direct connection to the circuit under test by clamping around the conductor, current carrying wire or structural member being tested.
-
EM-6981 | 9 KHz – 110 MHz -
Electro-Metrics Corp.
Current probes enable you to measure conducted current without direct connection to the circuit under test by clamping around the conductor, current carrying wire or structural member being tested.
-
Modus Test, LLC
Instrumentation• 16,128 Kelvin ChannelsApplications• Cres Test Characterization For Test Sockets / Probe Heads / Connectors• Package Testing / Qualification• Device Opens / Shorts Testing• MTC Compatible For Integrated Cycling / Stepping / Force Measurement• MTC-TC Compatible For Hot/cold Thermal Chamber Characterization
-
3700 -
Peaceful Thriving Enterprise Co Ltd
*2 x 6m retractable test leads.*Used as an extension cord for cars, trailers, boats and more.*Optional accessory included alligator clips, test probes and banana plugs.*The tester can be used with any multi meter or device equipped with banana jack connectors.
-
YAVTB000 -
6TL Engineering
When wiring a test fixture, you often have a need to join three or more wires onto the same test point. This module solves this problem, adding test points for manual test probes and a 4 position DIP switch. Circuits 1 and 2 feature up to 5 poles in parallel to increase the space for power supply terminals.
-
Amkor Technology, Inc.
With knowledge gathered from decades of supporting Tier 1 and emerging industry leaders, Amkor understands test solutions must address advanced technology, quality, performance and cost of test. We offer full turnkey solutions including wafer processing, advanced bump, wafer probe, assembly, final test, system-level test, burn-in and end-of-line services.
-
Acculogic Sprint 4510 -
Terotest Systems Ltd.
The Sprint 4510 family of flying probers are well known for their speed, reliability, ease of use and large world-wide installed base.Flying probe testers have few restrictions on access, require no test fixtures, and can test boards with virtually unlimited number of nets, allowing test developers to turn a program around in a short time.
-
GL Communications Inc.
Most equipment manufacturers and large enterprises prefer rack-based test tools as they are compact and higher density form factor solution for testing, monitoring, and troubleshooting network conditions. GL’s Multiple TDM Optical and Packet (mTOP™) rack enclosure can house any combination of USB based test equipment which are easily deployed and securely fixed to an equipment rack to provide extraordinary scalability to test switches, routers and end-to-end networks. These rack based platforms incorporates the basic test unit along with the necessary PC hardware, Windows® 10 64-bit operating system and remote accessibility via scripting and remote desktop. There are no moving parts with the unit, so reliability and longevity are integral. GL’s latest mTOP™ Probe stand-alone hardware variant is an all-in-one self-contained test instrument. The mTOP™ Probe can include any of the multiple TDM Optical and Packet interfaces USB device combined with the PC into one single box. The comprehensive mTOP™ Probe hardware unit is designed for easier portability and convenient for field testing which incorporates the testing features for multiple interfaces along with necessary PC hardware in a single box. GL’s USB based test equipment - PacketExpert™ (Ethernet), tProbe™ (T1/E1), USB T3/E3 (TDM), Dual UTAs (Analog/Wireless), and LightSpeed1000™ (SONET SDH) to support multiple interfaces in a compact rack space or included in a portable Probe unit.
-
Bierer & Associates, Inc
Digital DC Resistive Voltmeter has a single range of 0 – 2kV. The unit consists of a meter probe, second probe, and connector cable. This unit is designed to measure DC voltage between the negative return rail and overhead positive cantenary conductor used on transit systems. The five position selector switch located on the face, controls OFF, ON, and Test. The OFF positions are for storage and transit. The ON position is for measurements from 0 to 1999 volts with one-volt resolution. The T position tests basic meter functions and the digital display.